The store will not work correctly in the case when cookies are disabled.
We use cookies to make your experience better.To comply with the new e-Privacy directive, we need to ask for your consent to set the cookies. Learn more.
Electric motor and controller model is ETL certified to UL and CSA standards
Peer reviewed model (pneumatic motor and controller) is approved to be used with Acetone, Ethanol, Heptane, Hexane, Isopropyl Alcohol, Methanol, and Pentane.
CAUTION!
Across International is not responsible for caustic chemical related damage to the stainless steel reactor internal and external parts and components.
Never fill circulated heaters or chillers with water, always use Ai or manufacturer's recommended thermal fluid
Always leave ample fluid space in heater reservoir to allow fluid heat expansion
Impellar/Stirrer Options
Name
Stirrer Type A
Anchor
Stirrer Type B
Piched Marine
Stirrer Type C
Pitched Blade
Stirrer Type D
Square Blade
Stirrer Type E
Anchor with Upper Pitched Blade
Stirrer Type F
Dual Pitched Blade
Stirrer Type G
Triple Pitched Blade
Stirrer Type H
Double Helix
Shell and Tube Heat Exchanger
Standard Quick-change 316L Stainless Steel Propeller Agitator
220V, 50/60Hz, 1~Phase, 200 watts, 1/4 HP Rotation: 450 rpm max. (±8%) Starting torque: 3.0 N.m Rated torque: 1.54 N.m Built-in gearbox ratio: 3:1 to 180:1 Controller: Delta, UL listed
Pneumatic stirring motor
- Power: 1/4 HP - Rotation: 450 rpm max. (±8%) - Compressed air pressure range: 30 to 80 psi (0.2 to 0.55 MPa) - Working temperature: -10C to +70C - For constant use: set rpm to 80% of maximum rpm - Motor lubricant
Mobil Grease XHP 222, Lithium Complex, Blue, NLGI Grade 2
- For safety purpose, detach compressed air supply when not in use, left un-attended or at night - Do not run motor un-loaded - Set Air Adjuster to minimum at initial run, make sure motor is working properly, before increasing CFM - Before inspecting unit, stop the motor and detach air supply. Do NOT inspect unit when motor is in action. - Make sure exhaust port/hole is clear from any debris or blockage - Check every 2-3 days: Air Lubricant, Air Filter water drain
Port configuration
Lid: 12" triclamp Center motor port: 3" triclamp Drain port: 6" triclamp Drain port on/off valve: 2" triclamp Vacuum port: 1" triclamp Condenser recirculating fluid port: 1/2" female NPT Vessel jacket recirculating fluid port: 1" female NPT 50L/100L collection tank lid: 6" triclamp x 1, 1.5" triclamp x 4
Option 1: 10L x 2, 316L stainless steel, with manifold Option 2: 50L x 1, 304 stainless steel, with dolly (15.5" diameter, 23.5" height, 30" with dolly) Option 3: 100L x 1, 304 stainless steel, with dolly (15.5" diameter, 43" height, 49.5" with dolly)
Material
All wetted parts 316L grade stainless steel on main reactor body Rest of reactor in 304 grade stainless steel, including motor coupling, triclamps, temp/pressure gauge adapters, and chassis.
Main Condenser
Style: shell and tube heat exchanger Number of tubes: 70 Condensing area: 0.89 m2
Pressure
Ultimate vacuum level: 1 Torr
Temperature range
-55°C to +250°C (-67°F to +482°F)
Temperature sensor/display
Regular: BOOST.TTA.0101, -200C to 480C, 50.5 clamp Explosion proof: BOOST.TTA.0102, -200C to 480C, 50.5 clamp
Sealing gasket
Food grade Viton
Main Mounting Frame
Heavy duty 2 x 2" 304 grade stainless steel, mounted on four casters
Drain port ground clearance
Drain port: 19.5 inches Drain valve: 14 inches
Shipping Weight (Unit)
570 Lbs / 890 Lbs
Shipping Dimensions
50" x 40" x 90" (WxDxH)
Assembled Dimensions
34" x 32" x 80" (WxDxH) without condenser and receiving flasks
44" x 32 " x 91" (WxDxH) with condenser and receiving flasks
Compliance
ETL tested to UL and CSA standards C1D1 peer review by PSI (optional)
Electric motor and controller model is ETL certified to UL and CSA standards
Peer reviewed model (pneumatic motor and controller) is approved to be used with Acetone, Ethanol, Heptane, Hexane, Isopropyl Alcohol, Methanol, and Pentane.
CAUTION!
Across International is not responsible for caustic chemical related damage to the stainless steel reactor internal and external parts and components.
Never fill circulated heaters or chillers with water, always use Ai or manufacturer's recommended thermal fluid
Always leave ample fluid space in heater reservoir to allow fluid heat expansion
Impellar/Stirrer Options
Name
Stirrer Type A
Anchor
Stirrer Type B
Piched Marine
Stirrer Type C
Pitched Blade
Stirrer Type D
Square Blade
Stirrer Type E
Anchor with Upper Pitched Blade
Stirrer Type F
Dual Pitched Blade
Stirrer Type G
Triple Pitched Blade
Stirrer Type H
Double Helix
Shell and Tube Heat Exchanger
Standard Quick-change 316L Stainless Steel Propeller Agitator